CALL US TOLL FREE | 9am-7pm EST | M-F
LOCATIONS ACROSS THE NATION | TO SERVE THE ENTIRE COUNTRY
Leading Automotive Equipment Dealer Since 1987
ABOUT
CALL US TOLL FREE | 9am-7pm EST | M-F
LOCATIONS ACROSS THE NATION | TO SERVE THE ENTIRE COUNTRY
Leading Automotive Equipment Dealer Since 1987
ABOUT
RANGER RL-8500XLT
The new Heavy-Duty RL-8500XLT Combination Brake Lathe from Ranger features an extended capacity spindle and can turn a drum that?s up to 10-inches deep. The longer spindle and the relocated rear bushing provide the RL-8500XLT arbor with enough support to handle your heaviest drums, rotors, and flywheels.
The durably crafted RL-8500XLT brake lathe resurfaces brakes quicker and more precisely than any other lathing unit on the market today. Like the RL-8500, the RL-8500XLT features unlimited feed rate settings, allowing the user to modify resurfacing rates with an easy turn of the dial. Now you can decrease or amplify the cut duration for the perfect finish regardless of if you’re rushing through the first rough cut or performing a single-pass micro-finish. The RL-8500XLT brake lathe is the total package and comes with a strong bench plus ample tool storage backboards, so all your adapters are always nearby.
The RL-8500XLT Heavy-Duty Combination Brake Lathe by Ranger represents the future of brake lathe technology while simultaneously maintaining the classic design auto pros and technicians are most familiar with. By implementing DC servo motor controls for the cross feed and spindle feed drives, we’ve removed any need for cumbersome mechanical gear boxes and transmissions used in older brake lathes. Effectively, the RL-8500XLT Brake Lathe drastically decreases lifetime repair and maintenance cost when compared to other lathing units.
One of the common problems that plague other brake lathes is the vibration and chatter transfer that directly affects the tool-tip and leaves an imperfect cut on the machined surface. The RL-8500XLT Brake Lathe by Ranger is specifically designed to address this issue by eliminating the need for gear-driven mechanical drives and variable-speed transmission devices.
How stable is a Ranger brake lathe?
Ranger brake lathes replaced antiquated transmission / gears found on other brands. You would be surprised if you stood back and watched a brake lathe machine a finish cut on a rotor or drum or flywheel. Brake rotors are very smooth or should be. If you were to turn a rotor on any lathe then drop a hammer on the floor next to the lathe, you would see a noticeable degradation of the cut at the moment of impact. Vibration causes frequencies which gets transferred to the finish cut. Because our lathe does not use gears and transmissions, we completely eliminate multiple frequencies that could degrade the machining finish. The formation of surface roughness is usually the result of the tool feed rate, spindle rotational speed, tool geometry, the material properties, and relative tool-work vibration. Vibrations cause a significant variation of the frequency on the surface of the machined part.
The extended-edition RL-8500XLT Brake Lathe by Ranger simply offers the best features, best performance, best utility and best productivity possible in a brake lathing unit. If you’re seeking to expand and improve your service capabilities, the RL-8500XLT Brake Lathe is one of the strongest investments you can make.
Time-tested construction
Since its introduction nearly four decades ago, the design of our RL-8500 series brake lathes has been a favorite of brake service professionals everywhere. It's simple, it's fast, it's very precise and it runs forever. Features include our twin-cutter tool head with micrometer dials and quick drum-to-rotor changeover, adjustable speed settings allow you for quicker rough cuts or slower smooth cuts and an infinitely adjustable spindle-feed gear box with a variety of speed settings. Plus, our negative rake tooling yields one pass finish cuts every time, and the standard 1" arbor provides you a multitude of tooling and adapter choices from either Ranger or other aftermarket suppliers. Finish-cuts by the RL-8500 and the RL-8500XLT will meet or exceed factory specs.
Transmission free
The absence of gear-driven mechanical drives and variable-speed transmission devices reduces service and repair costs dramatically over the unit's lifetime
Dual servo motors
The revolutionary RL8500 brake lathe uses independent DC servo motors to control the cross feed and spindle feed drives eliminating the need for complex mechanical gear boxes and transmissions typically found on mechanically-driven brake lathes.
Heavy-duty bench included
Other manufacturers might try to make you pay extra for a sturdy bench, but Ranger throws it in as a standard accessory. Plenty of storage on the backboard to keep your tooling close at hand, a durable multi-compartment toolbox for adapters and a large chip “catch” funnel plus chip bin to keep your workspace both clean and safe--all this comes included in your RL-8500XLT purchase.
From rotors to drums and back again
A handy quick-change tool-head design gives operators the ability to easily change the setup from drums to rotors and vice-versa. Up-front controls are designed for minimal operator movement. A convenient tooling tray is positioned near the front of the lathe, so you can keep your preferred tools nearby.
A complete brake lathe tooling package comes standard
Micro-dial twin tool cutter, boring bar, inside floating adapters, self-aligning spacer, outside floating adapter, centering cones, spacers, double-taper adapters, hubless adapters, carbide cutting tools, 6-sided carbide cutting inserts, 1" arbor, arbor nut, back load spring, spare bulb for lamp, illustrated instruction manual, wrenches, high-impact anti-vibration bands, storage case and more all come standard with the RL-8500XLT Brake Lathe from Ranger.
Simple and secure
Our sensible ergonomic design allows you to work quickly and efficiently. Simple up-front controls are designed for minimal operator movement. Large bench with tool storage boards provide ample space for adapters and accessories.
Adjustable work lamps
Keeps your work area properly lighted, even in the darkest corners of your shop. Separate switch lets you turn on or off at your convenience. Clear Plexiglas safety shield protects the user without obstructing the view.
Catch the chips
Included chip catch funnels debris into a large chip bin, ensuring easy disposal and a tidy work area.
Optional extended RL-8500XLT truck adapter set
Our super-duty adapter package consists of an upgraded 1-7/8" arbor and a wide variety of adapters. This enormous set allows you to expand the coverage to handle virtually any vehicle, all the way through 1-ton trucks!
Rugged, user-friendly and hassle-free
Ranger brake lathes are easy to operate and durable enough to withstand the every day abuses of a busy shop environment. A super-heavy, forged, hardened, cast iron body combined with precision ground components and massive "floating spindles" make this one of the toughest, most dependable and trouble-free machines you will ever own.
Always at your service
Superior quality, durability and precision; that?s what makes Ranger the growing professional preference worldwide. Whatever your brake service equipment needs may be, you can rely on Ranger to deliver the right tools for the job. As a preferred supplier of quality automotive service equipment, our goal is simple: give our customers the best quality and value while providing unparalleled service and support. Why does Ranger offer you so much more? Because we don?t just believe in developing superior products, we believe in creating the automotive equipment solutions that make your job easier.
